Keepalived is used for IP failover between two servers. It facilities for load balancing and high-availability to Linux based infrastructures. It works on VRRP ( Virtual Router Redundancy Protocol ) protocol. We have running two load balance servers using HAProxy and now we need to implement VRRP between both servers. This tutorial will help you to configure KeepAlived, Use this tutorial to configure HAProxy on both servers.

Network Scenario:

  1. LB1 Server: 192.168.10.111 ( eth1 )
  2. LB2 Server: 192.168.10.112 ( eth1 )
  3. Virtual IP: 192.168.10.121

Now we are implementing ip failover setup between LB1 and LB2 servers.

Graphical representation of Fail over Setup:

Step 1: Install Required Packages

Use following command to install required packages to configure Keepalived on server.

# yum install gcc kernel-headers kernel-devel

Step 2: Install Keepalived

Keepalived is available in centos base repository. Install it using yum command line tool.

# yum install keepalived

Keepalived configuration File: /etc/keepalived/keepalived.conf

Step 3: Configure Keepalived on LB1.

Edit Keepalived configuration file on LB1 and add following configuration. Update all red highlighted values with your network and system configuration.

! Configuration File for keepalived

global_defs {
   notification_email {
     sysadmin@mydomain.com
     support@mydomain.com
   }
   notification_email_from lb1@mydomain.com
   smtp_server localhost
   smtp_connect_timeout 30
}

vrrp_instance VI_1 {
    state MASTER
    interface eth1
    virtual_router_id 51
    priority 101
    advert_int 1
    authentication {
        auth_type PASS
        auth_pass 1111
    }
    virtual_ipaddress {
        192.168.10.121
    }
}

Step 4: Configure KeepAlived on LB2.

Edit Keepalived configuration file on LB2 and add following configuration. While making changes in LB2 configuration file, make sure to set priority values to lower than LB1. For example below configuration is showing 100 priority value than LB1 has it 101.

! Configuration File for keepalived

global_defs {
   notification_email {
     sysadmin@mydomain.com
     support@mydomain.com
   }
   notification_email_from lb2@mydomain.com
   smtp_server localhost
   smtp_connect_timeout 30
}

vrrp_instance VI_1 {
    state MASTER
    interface eth1
    virtual_router_id 51
    priority 100
    advert_int 1
    authentication {
        auth_type PASS
        auth_pass 1111
    }
    virtual_ipaddress {
        192.168.10.121
    }
}

Step 5: Start KeepAlived

Start KeepAlived service using following command and also configure to auto start on system boot.

# service keepalived start
# chkconfig keepalived on

Step 6: Check Virtual IPs

By default virtual ip will assigned to master server, In case of master get down, it will automatically assigned to slave server. Use following command to show assigned virtual ip on interface.

# ip addr show eth1

Sample output

2: eth1: <broadcast,multicast,up,lower_up> mtu 1500 qdisc pfifo_fast state UNKNOWN qlen 1000
    link/ether 00:0c:29:6f:ed:60 brd ff:ff:ff:ff:ff:ff
    inet 192.168.10.111/24 brd 192.168.1.255 scope global eth1
    inet 192.168.10.121/32 scope global eth1
    inet6 fe80::20c:29ff:fe6f:ed60/64 scope link
       valid_lft forever preferred_lft forever

Verify IP Failover

1. Shutdown master server ( LB1 ) and check if ips are automatically assigned to slave server.

# ip addr show eth1

1. Now start LB1 and stop slave server ( LB2 ). IPs will automatically assigned to master server.

# ip addr show eth1

1. Watch log files to insure its working

# tailf /var/log/messages

Sample Output

Mar 19 17:30:24 localhost Keepalived_vrrp[6958]: VRRP_Instance(VI_1) Transition to MASTER STATE
Mar 19 17:30:25 localhost Keepalived_vrrp[6958]: VRRP_Instance(VI_1) Entering MASTER STATE
Mar 19 17:30:25 localhost Keepalived_vrrp[6958]: VRRP_Instance(VI_1) setting protocol VIPs.
Mar 19 17:30:25 localhost Keepalived_healthcheckers[6957]: Netlink reflector reports IP 192.168.10.121 added
Mar 19 17:30:25 localhost avahi-daemon[1407]: Registering new address record for 192.168.10.121 on eth1.IPv4.
Mar 19 17:30:25 localhost Keepalived_vrrp[6958]: VRRP_Instance(VI_1) Sending gratuitous ARPs on eth1 for 

I hope this article will help to setup IP failover between two load balance servers.